PropOne Prop Wash – 2 Sizes available

Taxes and shipping calculated at checkout. For more information, please see our terms of service page.

$ 17.75


Are you a reseller or retailer? – Click Here
Are you looking for bulk or contract pricing? – Click Here


Get the best out of your PropOne application! Use Prop Wash to thoroughly clean your metal surfaces.

Choice of 2 sizes available: 250mL and 1 Litre

Prop Wash is a metal cleaner for use on bronze and stainless steel which removes contamination you can’t see to properly prepare metal surfaces for the PropOne™: Foul Release Coating System… Read More

Do not use on anodes or polished metal surfaces!

Additional information

Weight N/A


Estimated Prop Wash Coverage Guide:
Propeller Size and Number of Blades

18″- 24″ 24″- 36″ 36″- 48″
Three or four blades Four or five blades Five blades
Running gear components to be cleaned One propeller 250mL Prop Wash 250mL Prop Wash 250mL Prop Wash
Two propellers 250mL Prop Wash 250mL Prop Wash 1 Litre Prop Wash
Two propellers, two rudders
two propeller shaft struts
250mL Prop Wash 250mL Prop Wash 1 Litre Prop Wash
Two propellers, two rudders, two propeller shaft struts & two trim tabs 250mL Prop Wash 1 Litre Prop Wash 1 Litre Prop Wash


PropOne Silicone Remover: 15 sqm per litre (3 sqm per 200mL)
PropOne Paint Stripper: 15 sqm per litre (3 sqm per 200mL)


Prop Wash

Surface Preparation

  1. Remove marine growth & existing coatings from metal surfaces.
  2. Abrade the metal with a mechanical grinder, wire wheel or by hand sanding (80-120Grit).
  3. For newly polished/repaired metals, abrade the metal surfaces to remove any slight surface oxidisation.
  4. Rinse metal surfaces with clean fresh water, ensuring that any abrasive residue is fully removed.

Surface Cleaning

  1. Apply Prop Wash using a clean cloth to scrub the surface. Do not allow to dry.
  2. Rinse surface with clean fresh water and wipe with a clean damp white cloth.
  3. Repeat until cloth shows no discolouration.
  4. Solvent wipe metal surfaces with acetone using a separate clean cloth.
  5. Keep metal surfaces dry and free from contaminants, do not touch surface.
  6. Continue with PropOne foul release coating application


PropOne Chemical Removal System, i.e.  Silicone Remover and Paint Stripper

Silicone Remover

  1. Remove all marine growth from surface.
  2. Apply Silicone Remover approx. 2mm thick using a brush. Tip: Prevent drying out by covering the treated area with cling-wrap in hot/windy climates.
  3. Do not allow remover to come in contact with water. 
  4. Leave in contact for 2-3 hours or until softened.
  5. Remove with a stiff nylon or wire brush, scrubbing in a circular motion.
  6. Wipe off any remaining residue with a xylene or toluene-soaked cloth.
  7. If any coating remains after scraping, apply second coat.
  8. Once done, proceed with Paint Stripper

Paint Stripper

  1. Apply Paint Stripper approximately 2mm thick using a brush or roller
  2. Leave  in contact for at least 15 minutes or until softened
  3. Scrape off coating with slight pressure and appropriately dispose of waste. A wire brush, strong scourer or paint scraping tool are recommended.
  4. If any coating remains after scraping, apply second coat.
  5. Wipe off any remaining residue with an acetone-soaked cloth, then hose-down surface to leave a bright metal surface.

PropOne Brief Application Guide

English Italian French Spanish

PropOne Chemical Removal Technical Data Sheet



Proven performance, worldwide. PropOne is a non-biocidal foul release coating that will protect your underwater metals. Increase speed and lower your fuel use!

Underwater Light Coating

PropOne ULC is a one pack, one coat solution designed to keep your underwater lights clean. Any growth  is easily dislodged by cleaning with a soft sponge or wiping with a gloved hand.

Customer Reviews

Based on 1 review
Ian Moore
PropOne is The 1

Prompt service and great product. Highly recommend GreenCorp Marine

    Your Cart
    Crystilium Marine Magic Eraser
    1 X $ 9.09 = $ 9.09 (incl. tax)